This Bundle Fits The Following Vehicles:

2010-2015 Mercedes-Benz GLK350

This Bundle Includes the Following Parts:

• 7-Way RV Wiring
• Pro Series Pilot Brake Control
• Generic BC Wiring Adapter

List of fitment years: 2010, 2011, 2012, 2013, 2014, 2015

ModuLite® HD Plus Protector w/Integrated Circuit & Overload Protection Trailer Light Power Module & Installation Kit Manufactured by: Tekonsha

The unit is rated for up to 4.2 amps for Turns/Stops circuits and 7.5 amps for the Taillight circuit

Universal ModuLite designed to be used on most vehicles plus the hard to wire vehicles

Draws power directly from the vehicle battery and uses less than 5mA of the vehicle circuit for sensing to turn the trailer functions on and off

Will work with either LED/Incandescent bulbs (vehicle & trailer)

Has integrated re-settable Short Circuit and Overload protection, to safeguard itself and the tow vehicle from shorts and installation wiring mishaps

Designed not to send feedback thru the vehicle circuits

The trailer brakes will override the hazard lamps when the brake is activated

Advanced circuitry works in all standard applications as well as vehicles with ST and STT pulse width modulation (PWM) systems

Interprets/decodes multiplex signal inputs (i.e. Audi, BMW, Mercedes and VW)

Will not work with vehicles with low-side switch

Can be used on a 2 wire or 3 wire system

All solid-state components in potted encapsulation

Includes integrated protective cover

Wiring Adapter, 4-Way Flat to 7-Way, Round Car End Manufactured by: Reese Towpower

The REESE Towpower pre-wired round blade 7-way connector, provides versatility in going from a 4-way flat to a 7-way standard plug. The 7-way connectors include electric brake, auxiliary, and backup circuits.

Provide versatility in going from 4-Flat to 7-Way standard plug

Pre-wired with 4-Flat and wired with butt connects and ring terminal

Easy wiring featuring prewired with 4-Flat and wired with butt connects and ring terminal

Features non-corroding brass terminals

Mounts to standard 7-Way bracket

Non-corrosive thermo plastic construction

Ring terminal already mounted to ground wire

12 volt and brake wires have butt connectors already attached

Trailer Brake Controller Installation Kit, Wire and Hardware Manufactured by: Tekonsha

This complete Tekonsha brake control installation kit contains everything needed to install a brake control in any vehicle that is not pre-wired for a brake controller. This kit includes all wires going to both the battery and the wires needed to go to the connector located at the rear of the vehicle.

OEM Style wiring harness

Easy to install

1-3 axles

Mounting Bracket, 7-Way OEM Connectors, Includes Screws and Nuts Manufactured by: Tow Ready

Mounts electrical connector to attachment bracket

Includes screws and nuts

Attractive point-of-purchase packaging

Pilot® Trailer Time-Delay Brake Controller for Trailers with 1-3 Axles Manufactured by: Pro Series

Pilot has a dark, smoke lens that is ideal for direct light applications, creating optimum visibility to read the large, two-digit display. Pilot has flexible mounting options and can be installed in any direction. Our microprocessor allows you the ability to read the display even when mounted upside down. The Pilot’s digital display shows voltage output to the brakes.

Large easy to read dual digital display shows:

• Properly wired control
• Voltage output to brakes (vs. a percentage)
• Connection to trailer

Dark smoke lens ideal for direct light applications; performs better than red lens

Protection against short circuit/loss of ground

Microprocessor allows control to be mounted upside down and still have a readable display

Standard mounting bracket included with optional ball mount available

For use on any 12 volt negative ground system

Plug & Play feature allows quick and easy connection

Limited lifetime warranty

Trailer Brake Controller Installation Kit, Universal Fit, 12 in. Length Manufactured by: Tekonsha

This universal harness is designed to mate with any Tekonsha brake controller. Simply wire in the harness and then plug into the controller to complete installation. This harness makes it easy to move the brake controller from one vehicle to another by just unplugging.

OEM style wiring harness

Quick and easy plug in connections

Allows controller to be unplug and moved to other vehicles

Color coded wire match brake control standards

Works on time proportional and time based controls

Positive locking connector stays connected when plug in tightly

Simple do it yourself instructions on every package

Fits REESE Towpower and Tekonsha brake controllers