Installation Instructions for Toyota Matrix and Pontiac Vibe

Part Numbers:

• 24812
• 60898
• 77183

Wiring Access Location:

• SUV3, SUV4

Tools Required:

• Wrenches: 19mm
• Drill Bits: None

Specifications:

• Max Gross Trailer Weight: 2,000 lb. (908 kg)
• Max Tongue Weight: 200 lb. (91 kg)
• Note: Do not exceed towing vehicle manufacturer’s rating.

Step-by-Step Instructions:

1. Raise Hitch:

   • Lift the hitch into position on the vehicle.

2. Install Fasteners:

   • Attach the hitch to the existing weldnuts in the frame rails using the provided bolts and washers.

3. Tighten Fasteners:

   • Torque all M12 CL10.9 fasteners to 92 Lb.-Ft. (125 N*M) using a torque wrench.

Hardware List:

• (6) M12 x 1.25 x 40mm CL10.9 Bolts
• (6) 1/2” Conical Washers

Safety Notes:

• Regularly inspect all fasteners and the hitch ball to ensure proper tightening.
• If the hitch is removed, plug any holes in the trunk pan or other body panels to prevent water and exhaust fumes from entering.
• Replace any damaged hitch or ball immediately.
• Always observe safety precautions and wear eye protection when working beneath the vehicle.
• Do not cut access or attachment holes with a torch.

Drawbar:

• Drawbar Kit: 3593
• Important: The drawbar must be used in the rise position only.

Compliance:

• This product complies with SAE J684, V.E.S.C. Regulation V-5, and safety requirements of the State of New York.

Additional Notes:

• For Toyota Matrix XRS and XR Sport models: The center fascia must be removed for hitch installation. (Fascia sold separately.)
• Check the hitch frequently to ensure all fasteners remain tight.

Installation Instructions for T-Connector Adapter for Pontiac Vibe

Part Numbers:

• 118458

Wiring Access Location:

• Inside the rear cargo area, behind the access panels on both sides.

Tools Required:

• Drill with 3/32" drill bit.
• Philips head screwdriver.

Step-by-Step Instructions:

1. Access Vehicle Wiring:

   • Open the rear tailgate and remove the cargo nets and cargo floor hatch to access the spare tire area.
   • Unscrew the nut holding the spare tire cover in place and remove the cover. Set aside all removed items carefully to avoid damage.
   • Remove the access panel doors on both sides to access the vehicle’s wiring connectors.

2. Locate the Taillight Wiring Harness:

   • On both the driver’s and passenger’s sides of the vehicle, locate the vehicle’s taillight wiring harness.
   • This harness will have a connection point matching the ends of the T-Connector.
   • Carefully separate the connectors, ensuring no damage to the locking tabs. Clean the connector surfaces if necessary.

3. Driver’s Side Connection:

   • Locate the access hole between the spare tire and the rear threshold.
   • Route the T-Connector end with the yellow wire, as well as the end with the brown and red wires, up through the access hole to the driver’s side access panel.
   • Attach both ends of the T-Connector to the driver’s side wiring harness, ensuring the connectors are fully inserted and secured with locking tabs.

4. Passenger’s Side Connection:

   • Route the T-Connector end with the green wire to the passenger’s side.
   • Repeat the steps for connecting the T-Connector to the passenger’s side wiring harness.

5. Ground Connection:

   • Locate a suitable grounding point near the connectors.
   • Clean the area of dirt and rustproofing.
   • Drill a 3/32" hole and secure the white wire using the provided eyelet and screw.
   • Caution: Avoid drilling into any exposed surfaces and verify what is behind the surface before drilling.

6. Mount the Converter Box:

   • Secure the T-Connector black box using the provided double-sided tape.
   • Use cable ties to secure the remaining harness, ensuring it is not in areas where it could be pinched, cut, or melted.

7. Reassembly:

   • Replace both access panels, the spare tire cover, cargo floor hatch, and cargo nets removed during installation.

8. Test Installation:

   • Test the installation with a test light or trailer to verify all connections are functioning correctly.

   Specifications:

   • Max. stop/turn light: 1 per side (2.1 amps).
   • Max. tail lights: (5 amps).

Hardware List:

• T-Connector adapter.
• Eyelet and screw.
• Double-sided tape.
• Cable ties.

Safety Notes:

• All connections must be complete for the T-Connector to function properly.
• Overloading circuits can cause fires. Do not exceed the towing manufacturer’s rating or the unit specifications.

Manufacturer Notes:

• Follow all warnings and installation instructions provided.
• Use a test light or trailer to confirm proper installation.
• Consult the vehicle owner’s manual for additional details.